基于 Fluent 的蒸汽喷射器结构研究与优化.pdf
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 基于 Fluent 的蒸汽喷射器结构研究与优化 蒸汽 喷射器 结构 研究 优化
- 资源描述:
-
2016年10
舰船电子对抗
第39卷第5期
SHLPBOARD ELECTRONIC COUNTERMEASURE
Vo 39 No, 5)
基于 Fluent的蒸汽喷射器结构研究与优化
王立慧、,许玉谋,冯静2
(1.中船重工海博威(江苏)科技有限公司,扬州225000;2.中国船舶重工集团公司第723研究所,扬州225001)
摘要:设计了一种用丁加热黏稠类物料的蒸汽喷射装置,基丁计算流体力学软件 Fluent数值模拟方法对不同结构
蒸汽喷射装置的速度场、温度场和压力场分布情况进行研究。结果表明,螺旋导柱截面宽度占据混合区域宽度约
40%6左右时,对蒸汽流的分散作用最住,速度情况和出口温度分布情况较为理想;螺旋导柱截面形状为正方形时其
压力和温度有最优解,为菱形时其湍动能分布有最优解。研究结果为改进菾汽喷射器结构和提升喷射器的工作效
率提供了必要的理论依据。
关键词:蒸汽喷射器;螺旋导枉:数值模拟
中图分类号:TQ2
文献标识码:A
文章编号:CN3-1113(2016)00-0106-07
DOI:10.16426j. cnki. jcdzdk.2016.05.027
Research and Optimization of Steam Iniector Structure Based on Fluent
WANG Li-hui.XU Yu-mou,FENG Jing
CSIC Hebowi (Jiangsu )Technology Development CoLtd, Yangzhou 225000, China
The 723 Insliule Of CSIC. Yangzhou 225001. China)
Abstract: T his paper designs a steam injection device to heat up the high viscosity material , studies
the distribution status of velocity field ,temperature field and pressure field of steam injection de
vices with different structures based on numerical simulation method calculating hydrodynamics
software Fluent. The results show that the dispersion effect Lo steam flow is the best the velocity
field and outlet temperature distribution are relatively ideal when the width of spiral guide column
section almost occupies 40 of the mixed zone width. The pressure and temperature distribution
has the optimal solution when the section shape of spiral guide column is square, the turbulent ki
netic energy distribution has the optimal solution when the section shape of spiral guide
columnn Is
diamond. The results could provide necessary theoretical basis for improving the steam injector
structure and raising Ihe injector work efficiency
Key words: steam injector; spiral guide column; numerical simulation
备内部容易出现物料堆积的情况,这就导致物料局
部达到所需温度时其余部分物料已经被过度加热
在各个行业中,往往需要对不同黏度的物料进使得物料成分发生大幅度变化り。本文围绕美国
行加热以达到排放和使用要求。对于诸如润滑油、Pick公司的蒸汽喷射器进行重新设计,并在原有螺
工业液体废料等具有相当黏度的液体来说,由于具旋导柱结构、螺旋导柱位置和蒸汽喷射孔研究的基
有一定黏度,其流动性往往较差,加热不易使物料温础上,对蒸汽喷射器内螺旋导柱尺寸及蒸汽喷射器
度得到均匀提升
螺旋截面形状进行研究,探究其内部结构的合理性。
对于浓浆类物料的加热来说,常规换热器装置
很难达到均匀的加热效果,物料的流动性较差,在设
收稿?坷数擱-0-30
展开阅读全文
文档分享网所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。



链接地址:https://www.wdfxw.net/doc80667975.htm