MIL-I-17563C美国军用标准.pdf

INCH-POUND
ML-1-17563C
28 September 1992
SUPERSEDING
MIL-I-17563B
4Apri11985
(See 6.6 and 6.9)
MILITARY SPECエ FICATION
IMPREGNANTS FOR CAST OR POWDER METAL COMPONENTS
This specification is approved for use by all Departments and
Agencies of the Department of Defense
I. SCOPE
1.1 Scope. This specification covers the requirements for impregnants
suitable for use in sealing the voids found in cast or powder metal components
which cause leaking of contained fluids. This specification covers the
impregnants in bulk form only and not after they have been used to impregnate the
metallic component
1.2 Classification. The impregnants shall be of the following classes( see
6.7)
Class
Suitable for service temperatures up to 300 degrees
Fahrenheit (F)(149 degrees Celsius(c))
Class 1a. Suitable for use on mortar shell castings up to 300 F
(149c)
C1asa2- Suitable for service temperatures up to500°F(260°C)、
Class 3 - Suitable for use where air pollution requirements apply
nd compatible with acrylic-nitrocellulose lacquer paint
system up to300°F(149°C)
NOTE: Classes 1, la, and 2 may or may not contain volatile photo
air pollution requirements are enforced,(ot be used where
chemically reactive solvents and should
Beneficial comments(recommendations, additions, deletions) and any pertinent
data which may be of use in improving this document should be addressed to:
Commander, ATTN: SEA 05Q42, Naval Sea Systems Command, 2531 National Center
Building 3, Washington, DC 20362-5160 by using the Standardization Documen
Improvement Proposal(DD Form 1426) appearing at the end of this document or
by letter
AMSC N/A
FSC 6850
DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited
Sourcehttp://www.assistdocs.com--downloaded:2008-03-13101:212
Check the source to verify that this is the current version before use
IL-エ?17563C
2. APPLICABLE DOCUMENTS
2. 1 Government documents
2.1.1 Specifications, standards and handbooks. The following specifica-
tions, standards, and handbooks form a part of this document to the extent
specified herein. Unless otherwise specified, the issues of these documents are
those listed in the issue of the Department of Defense Index of Specifications and
Standards (DODISS)and supplement thereto, cited in the solicitation (see 6.2)
SPECIFICATIONS
FEDERAL
0-S.809
Sulfuric Acid. Technical
P-C-111
Carbon Removing Compound
P-D-680
Dry Cleaning and Degreasing Solvent
TT-S-735
Standard Test Fluids: Hydrocarbon
PPP-C-96
Cans, Metal,28 Gage and Lighter
PPP-P.-704
Pails, Metal: (shipping, Steel, l Through
Gallons)
MILITARY
MIL -E-463
Ethyl Alcohol (for Ordinance Use)
MTL-T-5624
Turbine Fuel, Aviation, Grades JP-4, P-5 And
JP-5/JP8ST
MTL-L-7808
Lubricating Oil, Aircraft Turbine Engine
Synthetic Base, NATO Gode Number 0-148
S
Primer Coating, Cellulose-nitrate Modified
Alkyd Type, Corrosion-inhibiting, Fast-drying
(For Spray Application Over Pre treatment
Coating)
MTL-C-8514
Coating Compound Metal Pretreatment, Resin-acid
TL-E-9500
Ethylene Glycol, Technical
MTL-F-17111
Fluid Power Transmission
ML-H-17672
Hydr