ISO 15609-5-2011 金属材料焊接工艺规范和评定焊接工艺规范-第5部分：电阻焊接.pdf

Reference numberISO 15609-5:2011(E)ISO 2011 INTERNATIONAL STANDARD ISO15609-5Second edition2011-10-01Corrected version2011-12-01 Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 5:Resistance welding Descriptif et qualification dun mode opratoire de soudage pour les matriaux mtalliques Descriptif dun mode opratoire de soudage Partie 5:Soudage par rsistance ISO 15609-5:2011(E)COPYRIGHT PROTECTED DOCUMENT ISO 2011 All rights reserved.Unless otherwise specified,no part of this publication may be reproduced or utilized in any form or by any means,electronic or mechanical,including photocopying and microfilm,without permission in writing from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel.+41 22 749 01 11 Fax +41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2011 All rights reserved ISO 15609-5:2011(E)ISO 2011 All rights reserved iii Contents Page Foreword.iv1Scope.12Normative references.13Terms and definitions.24Technical contents of welding procedure specification.24.1General.24.2Product manufacturer.24.3Parent materials.24.3.1Composition.24.3.2Dimensions.24.4Common to all welding procedures.24.4.1Welding process.24.4.2Machine specification.34.4.3Joint design.34.4.4Surface and edge preparation.34.4.5Welding technique.44.4.6Resistance welding electrodes and auxiliaries.44.4.7Machine parameters and control settings.4Annex A(informative)Example of a WPS I:Planned process requirements.5Annex B(informative)Example of a WPS II:Quality acceptance criteria.6Annex C(informative)Example of a WPS III:Welding machine set-up.7Annex D(informative)Examples of parameters in resistance welding.8Bibliography.13-,-,-ISO 15609-5:2011(E)iv ISO 2011 All rights reserved Foreword ISO(the International Organization for Standardization)is a worldwide federation of national standards bodies(ISO member bodies).The work of preparing International Standards is normally carried out through ISO technical committees.Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee.International organizations,governmental and non-governmental,in liaison with ISO,also take part in the work.ISO collaborates closely with the International Electrotechnical Commission(IEC)on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives,Part 2.The main task of technical committees is to prepare International Standards.Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.Publication as an International Standard requires approval by at least 75%of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights.ISO shall not be held responsible for identifying any or all such patent rights.ISO 15609-5 was prepared by Technical Committee ISO/TC 44,Welding and allied processes,Subcommittee SC 6,Resistance welding and allied mechanical joining.This second edition cancels and replaces the first edition(ISO 15609-5:2004),which has been technically revised.ISO 15609 consists of the following parts,under the general title Specification and qualification of welding procedures for metallic materials Welding procedure specification:Part 1:Arc welding Part 2:Gas welding Part 3:Electron beam welding Part 4:Laser beam welding Part 5:Resistance welding Part 6:Laser-arc hybrid welding This corrected version of ISO 15609-5:2011 incorporates the following corrections:correction of the French title on the cover page of the English version;removal of 16 at the end of key item 17 in Figure D.1;replacement of the graphic in Figure D.5 raising the lower arrow near 10;removal of the second key item 13 in Figure D.5.Requests for official interpretations of any aspect of this part of ISO 15609 should be directed to the Secretariat of ISO/TC 44/SC 6 via your national standards body.A complete listing of these bodies can be found at www.iso.org.-,-,-INTERNATIONAL STANDARD ISO 15609-5:2011(E)ISO 2011 All rights reserved 1 Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 5:Resistance welding 1 Scope This part of ISO 15609 specifies requirements for the content of welding procedure specifications for resistance spot,seam,butt and projection welding processes.It is necessary to establish the acceptability of applying the principles of this part of ISO 15609 to other resistance and related welding processes before any qualification is undertaken.NOTE Details of ISO 15609(all parts for titles,see Foreword)are given in ISO 15607:2003,Annex A.Variables listed in this part of ISO 15609 are those influencing either weld dimensi