ISO 15610-2023 规范和鉴定金属焊接工艺材料—基于测试焊接耗材.pdf

Specification and qualification of welding procedures for metallic materials Qualification based on tested welding consumablesDescriptif et qualification dun mode opratoire de soudage pour les matriaux mtalliques Qualification base sur des produits consommables soumis essaisINTERNATIONAL STANDARDISO 15610Second edition 2023-02Reference number ISO 15610:2023(E)ISO 2023-,-,-iiISO 15610:2023(E)COPYRIGHT PROTECTED DOCUMENT ISO 2023All rights reserved.Unless otherwise specified,or required in the context of its implementation,no part of this publication may be reproduced or utilized otherwise in any form or by any means,electronic or mechanical,including photocopying,or posting on the internet or an intranet,without prior written permission.Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCP 401 Ch.de Blandonnet 8CH-1214 Vernier,GenevaPhone:+41 22 749 01 11Email:copyrightiso.orgWebsite:www.iso.orgPublished in Switzerland ISO 2023 All rights reserved-,-,-ISO 15610:2023(E)Foreword.ivIntroduction.v1 Scope.12 Normative references.23 Terms and definitions.24 Limits of the application of this document.24.1 Limits related to the welded joint.24.1.1 Parent material.24.1.2 Parent material thickness,t.34.1.3 Fillet weld throat thickness,a.34.2 Limits common to all welding processes.34.2.1 Multiple-process welding procedures.34.2.2 Welding positions.34.2.3 Welding consumables.34.2.4 Type of current.34.3 Limits specific for the welding process.34.3.1 Processes 131,132,133,135,136 and 138.34.3.2 Processes 141 and 15.44.3.3 Process 121.45 Preliminary welding procedure specification(pWPS).46 Qualification of the pWPS.47 Welding procedure qualification record(WPQR).4Annex A(informative)Example of a WPQR form.5Bibliography.6iii ISO 2023 All rights reserved Contents Page-,-,-ISO 15610:2023(E)ForewordISO(the International Organization for Standardization)is a worldwide federation of national standards bodies(ISO member bodies).The work of preparing International Standards is normally carried out through ISO technical committees.Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee.International organizations,governmental and non-governmental,in liaison with ISO,also take part in the work.ISO collaborates closely with the International Electrotechnical Commission(IEC)on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives,Part 1.In particular,the different approval criteria needed for the different types of ISO documents should be noted.This document was drafted in accordance with the editorial rules of the ISO/IEC Directives,Part 2(see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights.ISO shall not be held responsible for identifying any or all such patent rights.Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received(see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation of the voluntary nature of standards,the meaning of ISO specific terms and expressions related to conformity assessment,as well as information about ISOs adherence to the World Trade Organization(WTO)principles in the Technical Barriers to Trade(TBT),see www.iso.org/iso/foreword.html.This document was prepared by Technical Committee ISO/TC 44,Welding and allied processes,Subcommittee SC 10,Quality management in the field of welding,in collaboration with the European Committee for Standardization(CEN)Technical Committee CEN/TC 121,Welding and allied processes,in accordance with the Agreement on technical cooperation between ISO and CEN(Vienna Agreement).This second edition cancels and replaces the first edition(ISO 15610:2003),which has been technically revised.The main changes are as follows:process numbers have been updated in accordance with ISO 4063:2009;normative references have been updated;text has been editorially revised.Any feedback or questions on this document should be directed to the users national standards body.A complete listing of these bodies can be found at www.iso.org/members.html.Official interpretations of ISO/TC44 documents,where they exist,are available from this page:https:/committee.iso.org/sites/tc44/home/interpretation.html.iv ISO 2023 All rights reserved-,-,-ISO 15610:2023(E)IntroductionThis document is a part of a group of standards dealing with specification and qualification of welding procedures,details of which are given in ISO 15607:2019,Annex A.In ISO 15607,one of the methods for the qualification of welding procedures is