书签 分享 收藏 举报 版权申诉 / 6

Guide_to_understanding_Welding_Procedure.pdf

  • 上传人:attout
  • 文档编号:100378649
  • 上传时间:2021-09-10
  • 格式:PDF
  • 页数:6
  • 大小:62.86KB
  • 配套讲稿:

    如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。

    特殊限制:

    部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。

    关 键  词:
    Guide_to_understanding_Welding_Procedure
    资源描述:
    265 Birdsall Dr. Yorktown Heights, NY 10598 914 214 8460 www.aeis.us Guide to understanding Welding Procedure Specification (WPS), Procedure Qualification Record (PQR), and Welder Performance Qualification Record (WPQR) By Nagesh Goel, Director OPTECH TRAINING PARTNER An AEIS White Paper Page 2 of 6 CONTENTS Introduction. 3 What is Welding Procedure Specification (WPS)?. 3 What is Procedure Qualification Record (PQR)?. 3 What information should they include?. 4 What is a Prequalified WPS?. 4 What are SWPSs?. 4 What is Welder Performance Qualification Record (WPQR)? . 5 Acceptance Standards. 5 Documentation. 5 PQR/ WPQR Testing. 6 Weld Inspection and Testing. 6 Page 3 of 6 Introduction Welding requires skill. Determining “how to weld” requires knowledge regarding the materials being welded and welding process, among numerous other factors. Because of huge number of variables involved, the knowledge of the welding engineer and the skill of the welder need to be validated by a series of tests. All this information is documented on Welding Procedure Specification (WPS), Procedure Qualification Record (PQR), Welding Procedure Qualification Record (WPQR), and associated Test Reports. What is Welding Procedure Specification (WPS)? A WPS is a document that describes how welding is to be carried out in production. Its purpose is to aid the planning and quality control of the welding operation. They are recommended for all welding operations and most application codes and standards make them mandatory. What is Procedure Qualification Record (PQR)? A PQR is required when it is necessary to demonstrate that your company has the ability to produce welds possessing the correct mechanical and metallurgical properties. A welding procedure must be qualified in accordance with the requirements of an appropriate welding procedure standard, such as ASME Sec IX, as follows: 1. Produce a welding procedure specification (WPS) as stated above. 2. Weld a test piece in accordance with the requirements of your specification. The joint set up, welding and visual examination of the completed weld should be witnessed by a certified welding inspector such as an AWS certified CWI or an Inspection Body. The details of the test such as the welding current, pre-heat etc., must be recorded during the test. 3. Once the welding is complete the test piece must be subject to destructive and non destructive examination such as radiography and mechanical tests as defined by the welding procedure standard. This work must be carried out in a qualified laboratory but the Inspection Body may require witnessing the tests and viewing any radiographs. 4. If the test is successful you or the test body completes the appropriate documents which the test bodys surveyor signs and endorses. Page 4 of 6 What information should they include? Sufficient details to enable any competent person to apply the information and produce a weld of acceptable quality. The amount of detail and level of controls specified on a WPS is dependant on the application and criticality of the joint to be welded. For most applications the information required is generally similar to that recorded on a Procedure Qualification Record (PQR), except that ranges are usually permitted on thicknesses, diameters, welding current, materials, joint types etc. If a WPS is used in conjunction with an approved procedure qualification record (PQR) then the ranges stated should be in accordance with the approval ranges permitted by the PQR. However careful consideration should be given to the ranges specified to ensure they are achievable, so that these ranges represent good welding practice. What is a Prequalified WPS? Some codes, such as AWS D1.1, allow “Prequalified WPS”, whereby it is established that the WPS written per code will produce welds with correct mechanical and metallurgical properties. It is not necessary to prepare a PQR in such cases. However, the pre-qualified WPS have a specified range of parameters under which the weld must be produced. When welding variables fall outside these ranges, a WPS with supporting PQR must be prepared. What are SWPSs? In an effort to standardize and harmonize the process of WPS approvals, AWS started writing “Standard Welding Procedure Specifications (SWPSs)” with input from the pioneers and experts in the welding industry. An extensive testing program was undertaken whereby; these SWPSs were then supported by numerous PQRs. When the use of SWPSs is permitted by referencing code section, your company does not have to perform one or more procedure qualification tests. You can simply purchase the applicable SWPS for unlimited intra-company use from the American Welding Society (www.aws.org). Page 5 of 6 What is Welder Performance Qualification Record (WPQR)? Once the procedure is approved it is necessary to demonstrate that all your welders working to it have the required knowledge and skill to put down a clean sound weld. If the welder has satisfactoril
    展开阅读全文
      文档分享网所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。
    关于本文
    本文标题:Guide_to_understanding_Welding_Procedure.pdf
    链接地址:https://www.wdfxw.net/doc100378649.htm
    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    版权所有:www.WDFXW.net 

    鲁ICP备14035066号-3




    收起
    展开