MIL-PRF-83401.1H-2006.pdf

MIL-PRF-83401/1H 5 May 2006 SUPERSEDING MIL-PRF-83401/1G 18 March 1996 PERFORMANCE SPECIFICATION SHEET RESISTOR NETWORK, FIXED, FILM, STYLE RZ010, 14 PIN DIP This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers the associated requirements for style RZ010, 14 pin dual-in-line package (DIP) resistor networks. This style is available in all characteristics and resistance tolerances. This specification has two product levels, a high reliability, 100 percent burn-in screened M part number and a nonburn-in screened part number C. 1.2 Part or Identifying Number (PIN). Resistor networks covered by this specification are identified by a PIN which will consist of a basic number of this specification and a coded number. The PIN is in the following form: 100 percent burn-in screened network (M part number) M8340101 H1002FA | _ |_ Associated specification number Coded number Nonburn-in screened network (C part number) C8340101 H1002FA | _ |_ Associated specification number Coded number The coded number is derived in accordance with MIL-PRF-83401. AMSC N/A FSC 5905 INCH-POUND Comments, suggestions, or questions on this document should be addressed to: Defense Supply Center, Columbus ATTN: DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3990, or emailed to resistordla.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at http:/assist.daps.dla.mil. MIL-PRF-83401/1H 2 1.2.1 Schematics. The schematics of the resistor network are identified by a single letter in accordance with the drawings below. The resistor element RREF is the reference element used in determining the ratio accuracy (when applicable). 1.2.1.1 Standard resistance values. The standard resistance values and the resistance value designators for the J schematic are as specified in table I. TABLE I. Standard resistance values. Resistance designator R1 (ohms) R2 (ohms) Resistance designator R1 (ohms) R2 (ohms) A001 A002 A003 A004 A005 A006 A007 A008 A009 82 120 130 160 180 180 220 220 330 130 200 210 260 240 390 270 330 390 A010 A011 A012 A013 A014 A015 A016 A017 A018 330 330 1.5k 3.0k 180 270 560 560 620 470 680 3.3k 6.2k 270 270 560 1.2k 2.7k MIL-PRF-83401/1H 3 2. APPLICABLE DOCUMENTS * 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. * 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-83401 - Resistor Networks, Fixed, Film, and Capacitor-Resistor Networks, Ceramic Capacitor and Fixed, Film, Resistors, General Specification for. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standard Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia PA 19111-5094.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Associated specifications. The individual item requirements shall be in accordance with MIL-PRF-83401, as specified herein. 3.2 Interface and physical dimensions. The resistor shall meet the interface and physical dimensions specified on figure 1. 3.3 Power rating (70C). The power ratings for schematic A, schematic B, and schematic J shall be as specified in table II. MIL-PRF-83401/1H 4 TABLE II. Power ratings. Schematic Characteristic Element power rating (watts) Network power rating (watts) A C H K M V 0.1 0.2 0.2 0.2 0.1 0.7 1.4 1.4 1.4 0.7 B C H K M V 0.05 0.1 0.1 0.1 0.05 0.65 1.3 1.3 1.3 0.65 J C H K M V 0.025 0.050 0.050 0.050 0.025 0.6 1.2 1.2 1.2 0.6 3.4 Power conditioning. The power applied for power conditioning for schematic A, schematic B, and schematic J shall be 1.5 times rated power. 3.5 Voltage rating. The maximum continuous working voltage for each resistor shall not exceed 100 volts dc or ac rms. 3.6 Resistance. Minimum and maximum resistance values shall be as follows: Resistance Minimum Maximum tolerance resistance resistance (ohms) (megohm) B (0.1 percent) 100 1 D (0.5 percent) 100 1 F (1.0